Ask Question

There can be a one week lead time as these 80 durometer bushings are not normally stocked.

This is factory upgrade bushing featuring  a standard 80 durometer proprietary polyurethane material pre-installed into a CNC machined aluminum bracket.  With so much demand for these bushings we are making it that much easier to upgrade. Watch the video to see how they perform under pressure.  These bushings replace the fluid-filled  factory rubber bushings with Superpro Polyurethane Bushings that are built to last and properly engineering to increase performance.  The high-end polyurethane design eliminates the parasitic spring rate caused by staked bushings and increase service life. These bushings also provide more positive front arm location during spirited driving while also will reducing inner tire wear* due to toe deflection under braking. 

Set includes 2-Bushing sets to replace both bushings INSTALLED INTO FIGS BILLET BRACKETS

includes grease

no shop press required since we include the brackets, just bolt-in.


Fits:

2001-2005 LS430 (must remove teardrop factory taper washer)

2006+ IS Vehicles

2006+ GS vehicles

2015+ RC-F

2016+ GS-F

2015+ RC350


 Video of it in action


Install:

The bushing sits at the back of the front LCA which is held on by two bolts into the chassis and one nut that is threaded on to an extension of the arm.

You will need to remove both under-covers and the side bracket bolt that is attached to the #2 bushing bracket.

Remove the two bolts holding the bushing bracket (one with nut) and 2 side rail bracket 

Remove the rear nut that holds the bracket to the LCA.

Remove rear bushing bracket, this may require deflection of the front arm bushing or unbolting the front location to free preload   If too difficult you will need to remove the entire arm, sway bar and shock absorber. Contact FIGS is this is the case.

Install new bushings making sure the bevel on the bushing tube is oriented towards the front of the vehicle.

Reinstall rear nut to hold bushing in place but not to final torque. 

Reinstall 2 bolts plus nut  and 2 bolts of side bracket.   Long bolt through side rail bracket torque to 204Nm/ 150ft-lbs, short bolt with nut 86Nm/63ft-lbs, and the side rail bolts 50Nm/37ft-lbs. Apply final torque to the nut at the center of of the bushing 113Nm/ 83ft-lbs.

Verify clean cycling of the suspension by loading and unloading.  If any other OE or rubber bushings where loosened or replaced, load the suspension and then final torque them to prevent their premature wear. 

You done!


*Alignment is still required to benefit from tire wear reduction. 

Write a review

Please login or register to review

FRONT LOWER ARM REAR MOUNT #2 POLYURETHANE BUSHING 80 STANDARD INSTALLED IN BRACKET

  • Brand: FIGS Engineering
  • Product Code: G2ISHP-FRLCA-SP3491K-IN-BRKT
  • Availability: In Stock
  • $360.00


Related Products

FIGS MEGA ARMS GEN 2 IS / IS-F "RACE VERSION" V2

FIGS MEGA ARMS GEN 2 IS / IS-F "RACE VERSION" V2

VERSION 2 now shipping.  TECH DATA CNC machined 1018 steel end fittings. Formed stee..

$875.00

FIGS MEGA ARMS GEN2 IS/IS-F GEN3 GS ESSENTIAL KIT FOR LOWERING

FIGS MEGA ARMS GEN2 IS/IS-F GEN3 GS ESSENTIAL KIT FOR LOWERING

Making Lowering Simple The impact of lowering a second gen IS or 3rd gen GS is dramatic. Camber,..

$1,186.50 $1,305.15

SPC MASTER BUSHING INSTALL TOOL KIT

SPC MASTER BUSHING INSTALL TOOL KIT

Includes cups and threads to drive in just about any bushing imaginable.  We found it a great asse..

$720.00 $1,355.73

SPC BALL JOINT SERVICE KIT 40920

SPC BALL JOINT SERVICE KIT 40920

This is a ball joint service tool that seems to be just perfect for pressing out the lower knuckle..

$104.00 $204.47

Tags: G2ISHP-FRLCA-SP3491K-IN-BRKT, 2006+, IS, GS, Front, Lower, Arm, Rear, Mount, #2, Polyurethane, Bushing, 80, Standard, INSTALLED, IN, BRACKET, 3491, 3491-80